넳 넲

庆鸿慢走丝的报警号，一览表

FANUC伺服驱动器维修，西门子伺服电机维修，伦茨伺服马达销售，伺服控制器维修  ꄲ  设备维修  ꄲ  慢走丝  ꄲ  庆鸿  ꄲ  庆鸿慢走丝的报警号，一览表
这么多年，也没有看见谁发个报警号一览表，这个是从程序中提出来的
比如驱动器报警出现 100001，这查下表，1000，01就是X轴，
 
01(X),02(Y),04(Z),08(U),16(V),31(XYZUV)]
 
 
又比如报警1520，这个是HI-POWER PLC ABNORMAL，
 
HI-POWER就是那个HP放电板，不正常，有故障。
 
 
W5F MESSAGE,ALARM and ERROR CODE DEFINITION
     5  CPU_NUMBER_NOT_MITCH 
     6  SYSTEM DATAS ARE NOT MITCH LAST SHUT DOWN!
    10  CONTROL SYSTEM READY OK.
    20  CONTROL SYSTEM POWER READY OK!
    40  CONTROL SYSTEM SHUT DOWM OK
    60  SYSTEM PARAM.SET TO DEFAULT PARAM.
    62  SYSTEM DATE & TIME IS SETTED BEFORE NOW.
    64  SYSTEM DATE & TIME IS SETTED AFTER NOW.
    70  DEFAULT PARAM.SET TO SYSTEM PARAM.
    80  CONTROL SYSTEM SEND PARAM.TO AWT.MODULE OK!
    90  SYSTEM MEMORY POOL EMPTY
   100  X AXIS POSITION ERROR IN EPCIO MODULE.
   101  Y AXIS POSITION ERROR IN EPCIO MODULE.
   102  Z AXIS POSITION ERROR IN EPCIO MODULE.
   103  U AXIS POSITION ERROR IN EPCIO MODULE.
   104  V AXIS POSITION ERROR IN EPCIO MODULE.
   200  GLOBAL VARIABLE ERROR WHEN VALUE OPERATOR
   201  GLOBAL VARIABLE ERROR WHEN VALUE OPERATOR
   202  SYSTEM VARIABLE ERROR WHEN VALUE OPERATOR
   203  H. VARIABLE ERROR WHEN VALUE OPERATOR
   204  D. VARIABLE ERROR WHEN VALUE OPERATOR
   210  ACOS FUNCTION ERROR WHEN VALUE OPERATOR
   211  SQET FUNCTION ERROR WHEN VALUE OPERATOR
   212  VALUE CODE ERROR WHEN VALUE OPERATOR
   220  RIGHT "]" MISS WHEN VALUE OPERATOR
   221  LEFT "[" MISS WHEN VALUE OPERATOR
   230  OPERATOR UNIT TOO MANY WHEN VALUE OPERATOR
   250  VALUE CODE ERROR WHEN VALUE OPERATOR
   251  DIVION IS ZERO WHEN VALUE OPERATOR
   260  VALUE OUTSIDE MAX.RANGE WHEN VALUE OPERATOR
   261  VALUE OUTSIDE MIN.RANGE WHEN VALUE OPERATOR
   262  RULE ERROR WHEN VALUE OPERATOR(Ex:20. 5)
  1000(**)  DRIVER ALARM[**=01(X),02(Y),04(Z),08(U),16(V),31(XYZUV)]
  1100(**)  TOUCH HARD LIMIT SWITCH[**=01(X),02(Y),04(Z),08(U),16(V),31(XYZUV)]
  1200(**)  TOUCH SOFT LIMIT SWITCH[**=01(X),02(Y),04(Z),08(U),16(V),31(XYZUV)]
  1300(**)  ERROR OVERFLOW[**=01(X),02(Y),04(Z),08(U),16(V),31(XYZUV)]
  1400  IO232 LINK OFF
  1450  PG232 LINE OFF or FEEDBACK OFF
  1480  WATER EMPTY IN TANK
  1500  DEVICE POWER OFF
  1520  HI-POWER PLC ABNORMAL
  1540  SPARK POWER RELAY CAN'T ON BEACUSE WIRE BREAK
  1541  SPARK POWER RELAY CAN'T ON BEACUSE WIRE NOT FOUND
  1542  SPARK POWER RELAY CAN'T ON BEACUSE CE.FUNC.
  1600  AWT.MODULE ERROR
  1610  OVER LIMIT FRICT SENSOR
  1620  WIRE THROUGH TIME OUT
  1621  WIRE THROUGH CAN'T PASS LOW GUILD
  1622  WIRE THROUGH FAILURE
  1640  WIRE BROKEN MESSAGE
  1699  PRESS "STOP" KEY TO ABORT AWT.CMD
  1695  Z AXIS MOVING,MAY BE TOUCH OBJECT
  1699  PRESS "STOP" KEY TO ABORT AWT.CMD
  1703  WIRE THROUGH CAN'T PASS SENSOR
  1729  UP GUILD SENSOR ERROR
  1730  ENCODER ERROR
  1731  HEATOR ERROR
  1732  HEATOR ERROR
  1734  AIR TOO WEAK(UP 5KG/CM/CM)
  1735  DURING DO ANNEAL,WIRE BROKEN
  1736  AWT MODULE ERROR
  1737  CLIPPER POSITION SENSOR
  1744  DURING DO ANNEAL,WIRE BREAK SWITCH NOT READY
  1746  AC.DRIVER ALARM AT AWT.MODULE
  1800  AWT.MODULE SET PARAMETER or LINK ERROR
  1810  AWT.MODULE LINK OFF
  1820  AWT.MODULE DRIVER ALARM
  1830  AWT.MODULE AIR TOO WEAK(UP 5KG/CM/CM)
  1840  WIRE EMPTY in AWT.MODULE
  2000  PRESS STOP KEY WHEN TABLE MOVING.
  2010  DRIVER or MOTOR ERROR WHEB TABLE MOVING.
  2100  GAP VOLTAGE ERROR WHEN SEARCH EDGE.
  2200  EDGE or VERT.MOVE DIST.TOO LONG
  2300  PITCH PARAMETER TXT NOT FOUND
  2400  NOT VERT.PT.WHEN DADB OPERATOR
  2500  SEARCH HOLE OPEN RANGE OVERFLOW SETTED
  2600  SPARK*OFFSET(NEW) REGISTER DEFAULT DATA BASE
  2610  SPARK*OFFSET(NEW) REGISTER USER DATA BASE
  2602  SPARK*OFFSET(MODIFY) REGISTER DEFAULT DATA BASE
  2612  SPARK*OFFSET(MODIFY) REGISTER USER DATA BASE
  2700  SPARK&OFFSET REGISTER or SET FAILURE(EDIT THIS FILE)
  2740  SPARK&OFFSET REGISTER or SET FAILURE(ABSENT IN DATA BASE)
  2800  NOT VERT.PT.WHEN ALIGN OPERATOR
  2810  UP,DOWN GUIDE DISTANCE ERROR WHEN ALIGN MOVE
  2900  CORNER DATA REGISTER DATA BASE
  2902  CORNER DATA(MODIFY) REGISTER DATA BASE
  3000  CAN'T COMPUTER OUTSIDE CENTER!
  4000  OPEN FILES TOO MANY IN EDIT MODULE
  4010  MEMORY ERROR IN EDIT MODULE
  4020  MEMORY ERROR IN EDIT MODULE
  4050  CLOSE FILE DISABLE WHEN THIS FILE CUTTING
  4080  EDIT_COPY_ERROR
  4100  NC.TEXT FORMAT ERROR
  4110  NC.MEMORY ERROR
  4200  MOVE CURSOR OUTRANGE IN EDIT MODULE
  4210  SEARCH N CODE IN EDIT MODULE
  4300  SIMULATE OPERAROR PRESS ESC KEY ABORT
  4400  RECEIVER or SENDER OK WHEN DNC OPERATING
  4410  DNC INPUT WAIT TOO LONG TIME
  4420  DNC INPUT WAIT CHAR TOO LONG TIME
  4430  DNC ABORT by USER
  4450  DNC TRANSFER TABLE ERROR
  4500  CAN'T MODIFY,DELETE,SAVE FILE WHEN EDITING
  4510  OPEN FILES TOO MANY WHEN EDITING
  4520  OPEN FILE ERROR
  4600  INSERT STRING IS NOT SETTED
  4605  INSERT STRING LENGTH TOO OVERFLOW
  4610  SEARCH STRING IS NOT SETTED
  4620  SEARCH STRING IS NOT FOUND
  4630  REPLACE STRING IS NOT SETTED
  4640  REPLACE STRING IS NOT FOUND
  4700  SPARK OFFSET SET
  4720  SET NC DATA INTO NC.PGM.
  4721  SET TAPER DATA INTO NC.PGM.
  4722  SET CONRER(INNER0) DATA INTO NC.PGM.
  4723  SET CONRER(INNER1) DATA INTO NC.PGM.
  4724  SET CONRER(OUTER0) DATA INTO NC.PGM.
  4725  SET CONRER(OUTER1) DATA INTO NC.PGM.
  4726  SET AWT.WORK DATA INTO NC.PGM.
  4800  EDIT BLOCK ERROR MANY WHEN EDITING
  4810  EDIT BLOCK ERROR MANY WHEN EDITING
  4850  PRESS STOP WHEN BROWSERING FILE NAME
  4860  FILE NAME NOT EXIST WHEN EDITING
  4870  NC.PGM.COUNT TOO MANY WHEN EDITING
  4880  MEMORY ERROR WHEN EDITING
  4900  PASSWORD NOT MITCH WHEN INPUTING PASSWORD
  4910  PASSWORD TOO LONG WHEN INPUTING PASSWORD
  4920  PASSWORD NOT MITCH WHEN INPUTING PASSWORD
  4930  MODIFY PARAM.ERROR WHEN PASSWORD ERROR
  5000  M.CODE STOP WHEN RUNNING NC.PGM.
  5010  SINGLE STOP WHEN RUNNING NC.PGM.
  5020  WIRE BREAK WHEN RUNNING NC.PGM.
  5030  WIRE SHORT WHEN RUNNING NC.PGM.
  5040  PRESS STOP KEY FEEDHOLD WHEN RUNNING NC.PGM.
  5050  SYSTEM SLEEP ACTION.
  5060  PGM.START POINT NOT MITCH WHEN SKIM CUT OP.
  5070  BLOCK SKIP KEY IS PRESSED WHEN RUNNING NC.PGM. 
  5080  EXCHANGING DEVICE SWHEN RUNNING NC.PGM.
  5090  WAIT PLC MODULE INPUT SIGNAL
  5100  WIRE EMPTY WHEN RUNNING NC.PGM.
  5110  COOLER ALARM WHEN PGM.CUT
  5120  M20 STOP WHEN PANEL KEY M20-STOP ON
  5121  M21 STOP WHEN PANEL KEY M21-STOP ON
  5122  M22 STOP WHEN AWT CUT MODE =M22 MODE.
  5200  CONTROLLER SYSTEM USE OVERTIME!
  5210  CONTROLLER SYSTEM USE OVERTIME!
  5220  CONTROLLER SYSTEM USE OVERTIME!
  5230  CONTROLLER CPU ID. ERROR
  5500  TRACER PATH ERROR WHEN RUNNING NC.PGM.
  5600(**)  MEM JOG MOVE FINISH
  5700(**)  MEM JOG MOVE ABORT
  5800  MEM.START CUT AT INITIAL MEM.CUT
  5810  MEM.START CUT CONTIUNE AFTER MEM.CUT STOP
  5900  MEM_CUT_MSG_FINISH
  5920  MEM_CUT_MSG_ABORT
  6000(**)  DRIVER ERROR WHEN RUNNING NC.PGM.
  6100(**)  TABLE TOUCH LIMIT SWITCH WHEN RUNNING NC.PGM.
  6200(**)  TABLE OUTRANGE SOFTWARE LIMIT AREA WHEN RUNNING NC.PGM.
  6300  XY-PLANE POINT ERROR BETWEEN MOTION AND SENDER MODULE
  6350  JOG CMD.MOVE ERROR IN MEM.CUT
  6380  MOTION WORK DATA ERROR
  6400  IO232 MODULE ERROR WHEN MEM.CUTTING
  6450  RE-CUT MOTION DATA ERROR AFTER PRESSING STOP KEY
  6480  NCODE NOT FOUND WHEN EXECUTE NCODE OPERATOR 
  6500  MEM_ERROR_AWT_THRU_MISS_OVERCOUNT
  6610  AWT.FEED WIRE CMD.SET
  6615  AWT.FEED WIRE FINISH
  6620  AWT.CUT WIRE CMD.SET
  6625  AWT.CUT WIRE FINISH
  6630  AWT.HANDLE WIRE CMD.SET
  6635  AWT.HANDLE WIRE FINISH
  8000  HOLE OPERATOR WHEN RUNNING NC.PGM.
  8100  NC.FILE IS MODIFIED WHEN RE-START CUT.
  8200  START NOT AT VERT.PT WHEN BEGIN CUT.
  8300(?)  CUT PATH OUT OFF TABLE TRAVEL(?=1(X),2(Y),4(U),5(V)).
  9000  START WORK ERROR WHEN RUNNING NC.PGM.
 10100  DATA CAN'T BE MODIFIED IN THIS STATE
 10200  THE FUNCTION CAN'T EXECUTE BECAUSE TABLE BUSING
 10300  THE FUNCTION CAN'T EXECUTE.
 10400  DATAS CAN'T BE SETTED OR MODIFYIED WHEN RUNNING NC.PGM.
 10500  AXIS ROTARY CAN'T SETTED UNDER THIS STATE
 10600  LIMIT ACTIVE WHEN PRESS START KEY
 12000  RANGE ERROR AT INPUTING FLAG DATA
 12010  RAGNE ERROR AT INPUTING CHAR DATA
 12020  RANGE ERROR AT INPUTING UNSIGNED CHAR DATA
 12030  RANGE ERROR AT INPUTING INTEGER DATA
 12040  RANGE ERROR AT INPUTING LONG INTEGER DATA
 12050  RANGE ERROR AT INPUTING DOUBLE DATA
 12080  DATA TYPE NOT MITCH WHEN INPUTING DATA
 16010  AWT_DRIVER_ERROR            
 16020  AWT_AIR_WEAK_ERROR          
 16030 AWT_WIRE_EMPTY_ERROR
 16040 AWT_PARAM_NULL_ERROR
 16050 AWT_WORK_STOP_KEY
 16060 WIRE BREAK by CLIPPER BEFORE ANNEAL PROCESS
 16101 AWT_THRU_OVER_TIMER_ERROR
 16102 AWT_THRU_OVER_COUNT_ERROR
 16103 AWT_THRU_OVER_DIST_ERROR
 16104 AWT_THRU_WAIT_STOP_ERROR
 16105 AWT_THRU_ANNEAL_ERROR
 16106 AWT_THRU_CUT_ERROR
 16107 AWT_THRU_CUT_OVER_TIME_ERROR
 16108 AWT_THRU_WASTE_OVER_TIME_ERROR
 16109 AWT_THRU_HEATER_ERROR
 16110 AWT_THRU_CLIP_WIRE_ERROR
 16201 AWT_CUT_OVER_TIMER_ERROR
 16202 AWT_CUT_FEED_ERROR
 16203 AWT_CUT_WAIT_STOP_ERROR
 16204 AWT_CUT_ANNEAL_ERROR
 16205 AWT_CUT_CUT_ERROR
 16206 AWT_CUT_CUT_OVER_TIME_ERROR
 16207 AWT_CUT_WASTE_OVER_TIME_ERROR
 16208 AWT_CUT_OVER_TIME_ERROR
 16209 AWT_CUT_HEATER_ERROR
 20010(?*????) AXIS GEAR RATION OUTRANGE(0.05~20.)WHERE *:0(X),1(Y),2(Z),3(U),4(V),5(B)
 30000  INTERPRETER MODULE ERROR
 30010  FILE NAME ERROR IN INTERPRETER MODULE
 30020  LOOP LESS IN INTERPRETER MODULE
 30030  SUBROUNT FILE NAME IN INTERPRETER MODULE
 30040  NC.PGM.FILE NAME ERROR IN INTERPRETER MODULE
 30050  BLOCK NOT EXIST IN INTERPRETER MODULE
 30060  BLOCK FORMAT ERROR IN INTERPRETER MODULE
 30070  FETCH NC.TEXT ERROR IN INTERPRETER MODULE
 30080  SYSEM POOL EMPTY IN INTERPRETER MODULE
 30110  N.CODE ERROR IN INTERPRETER MODULE
 30120  O.CODE ERROR IN INTERPRETER MODULE
 30130  SUBROUNT DEEP LEVEL OVER 8 IN INTERPRETER MODULE
 30150  COORDINAGE TRANSFER ERROR IN INTERPRETER MODULE
 30180  SYNC.COMMAND OVERFLOW
 30200  ARC COMMAND R=0 IN INTERPRETER MODULE
 30210  ARC COMMAND R VALUE ERROR IN INTERPRETER MODULE
 30220  ARC I,J COMMAND ERROR IN INTERPRETER MODULE
 30230  ARC K,L COMMAND ERROR IN INTERPRETER MODULE
 30262  RULE ERROR WHEN VALUE OPERATOR(Ex:20. 5)
 30300  MDI. COMMAOND ERROR IN INTERPRETER MODULE
 30310  GCODE ILLEGAL IN INTERPRETER MODULE
 30320  G10 SETTED INSUFFICIENT DATA.
 30330  WORK COORD.RULE ERROR(COMP.OFF,VERT.PT,TAPER ANGLE=0).
 30340  AXIS MIRROR&EX.&ROTARY&SCALE ERROR by G53 and RECORD PT MOVING.
 30350  NOT AT VERT.PT ERROR by G53 and RECORD PT MOVING.
 30360  NOT AT ZERO.PT(UV) by WORK COORD.MOVING.
 30601~30609 G34 SET VALUE OUTSIDE RANGE
 30610  DATAS ARE NOT FOUND by G34 in DATAS BASE  
 30710  DIVIDE ZERO WHEN VARIABLE OPERATOR 
 30720  SQRT MINUS WHEN VARIABLE OPERATOR
 30730  A ADDRESS VALUE MISS WHEN VARIABLE OPERATOR
 30740  A ADDRESS VALUE MISS WHEN VARIABLE OPERATOR
 30750  B ADDRESS VALUE MISS WHEN VARIABLE OPERATOR
 30760  C ADDRESS VALUE MISS WHEN VARIABLE OPERATOR
 30800  SKIM OPERATOR SETTED ERROR(start.end pt. not MITCH)
 31000  MACRO COMMAND ERROR IN INTERPRETER MODULE
 31110  DIV=0 ERROR IN INTERPRETER MODULE
 31120  SQER ERROR IN INTERPRETER MODULE
 31130  H.VARIALE ERROR IN INTERPRETER MODULE
 31140  H.VARIABLE A ADDRESS ERROR IN INTERPRETER MODULE
 31150  H.VARIABLE B ADDRESS ERROR IN INTERPRETER MODULE
 31160  H.VARIABLE C ADDRESS ERROR IN INTERPRETER MODULE
 31200  GLOBAL VARIABLE ERROR IN INTERPRETER MODULE
 31201  GLOBAL VARIABLE ERROR IN INTERPRETER MODULE
 31202  SYSTEM VARIABLE ERROR IN INTERPRETER MODULE
 31203  H.VARIABLE ERROR IN INTERPRETER MODULE
 31204  D.VARIABLE ERROR IN INTERPRETER MODULE
 31210  ACOS FUNCTION ERROR IN INTERPRETER MODULE
 31211  SQET FUNCTION ERROR IN INTERPRETER MODULE
 31212  VALUE CODE ERROR IN INTERPRETER MODULE
 31220  RIGHT "]" MISS IN INTERPRETER MODULE
 31221  LEFT "[" MISS IN INTERPRETER MODULE
 31230  OPERATOR UNIT TOO MANY IN INTERPRETER MODULE
 31250  VALUE CODE ERROR IN INTERPRETER MODULE
 31251  DIVION IS ZERO IN INTERPRETER MODULE
 31260  VALUE OUTSIDE MAX.RANGE IN INTERPRETER MODULE
 31261  VALUE OUTSIDE MIN.RANGE IN INTERPRETER MODULE
 31262  RULE ERROR WHEN VALUE OPERATOR(Ex:20. 5)
 34000  TAPER_ERROR_ID
 34010  TAPER_ERROR_START_RULE
 34100  INVERT TAPER ANGLE ERROR
 34111  INVERT TAPER ANGLE ERROR WHEN SKIP HANDLE
 35000  CORNER ERROR ID
 35010  CORNER ERROR WHEN PATH LINE-LINE
 35020  CORNER ERROR WHEN PATH LINE-ARC
 35030  CORNER ERROR WHEN PATH ARC-LINE
 35040  CORNER ERROR WHEN PATH ARC-ARC
 36000  COMP.ERROR ID
 36010  COMP.ERROR START RULE
 36020  COMP.ERROR END RULE
 36500  COMP.ERROR OVERCUT
 36510  COMP ERROR OVERCUT WHEN SKIP OVERCUT HANDLE
 4?***  AXIS HOME PT.ERROR(?=X1,Y2,Z3,U4,V5)(***:um)

三菱慢走丝维修 三菱慢走丝XYZ轴伺服电机维修 三菱慢走丝XYZ轴伺服驱动器维修 三菱慢走丝系统维修
FANUC慢走丝维修 FANUC慢走丝XYZ轴伺服电机维修 FANUC慢走丝XYZ轴伺服驱动器维修 FANUC慢走丝系统维修
沙迪克慢走丝维修 沙迪克慢走丝XYZ轴伺服电机维修 沙迪克慢走丝XYZ轴伺服驱动器维修 沙迪克慢走丝系统维修
庆鸿慢走丝维修 庆鸿慢走丝XYZ轴伺服电机维修 庆鸿慢走丝XYZ轴伺服驱动器维修 庆鸿慢走丝系统维修
西部慢走丝维修 西部慢走丝XYZ轴伺服电机维修 西部慢走丝XYZ轴伺服驱动器维修 西部慢走丝系统维修
夏米尔慢走丝维修 夏米尔慢走丝XYZ轴伺服电机维修 夏米尔慢走丝XYZ轴伺服驱动器维修 夏米尔慢走丝系统维修
徕通慢走丝维修 徕通慢走丝XYZ轴伺服电机维修 徕通慢走丝XYZ轴伺服驱动器维修 徕通慢走丝系统维修
牧野慢走丝维修 牧野慢走丝XYZ轴伺服电机维修 牧野慢走丝XYZ轴伺服驱动器维修 牧野慢走丝系统维修
日立慢走丝维修 日立慢走丝XYZ轴伺服电机维修 日立慢走丝XYZ轴伺服驱动器维修 日立慢走丝系统维修
苏三光慢走丝维修 苏三光慢走丝XYZ轴伺服电机维修 苏三光慢走丝XYZ轴伺服驱动器维修 苏三光慢走丝系统维修

慢走丝

——★★★【承接维修单◆免费检测◆十五年代理销售服务更专业】★★★——
深圳市诚弘欣科技有限公司专业致力于伺服电机、驱动器、变频器等工控配件销售及维修的公司。
联系人:李仁 
联系电话：0755-29613587
联系手机:13554907082 微信号
网址：http://www.chxsz.com  www.oil-gift.com  www.szsfwx.com   QQ:184860417、1473293320

YASKAWA 电机ELECTRIC UGTMEM-03LBB11阿奇慢走丝马达UGTMEM-06LBBLL
100430039 轴 马达 UGTMEM-06LBB31 ABB 夏米尔 慢走丝机用联系手机:13554990546 微信号
夏米尓23UPZ轴马达UGTMEM-06LBA11运丝电机UGTMEM-06LBB31
原装 联系手机:13554990546 微信号夏米尔电机 UGTMEM-06LBB31 ABB电机 UGTMEM-03LBB11

苏三光慢走丝松下伺服驱动器MSDA043D1A维修MSDA023D1A
苏三光慢走丝松下伺服驱动器MSDA083D1A维修MSDA103D1A
夏米尔慢走丝电机维修UGTMEM-06LBB41 联系手机:13554990546 微信号安川（ABB)伺服电机维修
沙迪克AQ360LS慢走丝U轴Y轴专用驱动器维修SGDM-04AC-SD2B安川驱动器

 

——★★★【承接维修单◆免费检测◆十五年代理销售服务更专业】★★★——
深圳市诚弘欣科技有限公司专业致力于伺服电机、驱动器、变频器等工控配件销售及维修的公司。
联系人:李仁 
联系电话：0755-29613587
联系手机:13554907082 微信号
网址：http://www.chxsz.com  www.oil-gift.com  www.szsfwx.com   QQ:184860417、1473293320


沙迪克慢走丝驱动器维修SGDM-04AC-SD2A安川驱动器
沙迪克慢走丝驱动器维修SGDM-02AC-SD2安川驱动器
沙迪克慢走丝驱动器维修SGDM-08AC-SD2安川驱动器
DV88010LDM04 松下驱动器维修 沙迪克电火花专用松下伺服器维修
专业维修沙迪克伺服器，安川 04AC SGDM-08AC-SD2B,伺服器维修
沙迪克慢走丝驱动器维修sgdm-a3ac-sd2安川伺服驱动器维修
Panasonic 松下MSMA012A1N马达 沙迪克张力马达
SGMPH-04ABA-SF22 沙迪克 安川伺服电机 马达 九成新
SGMAH-01ABA-SF11 沙迪克 安川伺服电机 马达 九成新
SGMAH-A3ABA-SF11 沙迪克 安川伺服电机 马达 九成新
松下伺服驱动器、MQDA023D1A33.MQDA043D1A33

台湾群基火花机专用马达-SANYO/三洋直流伺服电机M818T-031
松下伺服驱动器 MSD043P1E MSD023P1E MSD013P1E 已测

三菱MITSUBISHI慢走丝  
FA-S
FA10S
FA20S
FAPS
FA20PS
MV2400S
MV1200S 
FX2K
FA30VM 
MX600
MP1200
MV1200R
FA10
DWC-200HA
FA10M
EA12D

法兰克FANUC慢走丝
C600iA
X-C400iA 
C800iA 
α-C400iB
α-C600iB
α-C800iB

沙迪克SODICK慢走丝
AQ400Ls
AQ360Ls
AQ560LS
AQ535L 
AQ325L
ALN400Gs
AG400LS
AD360LS 
AQ400L
AQ600LS
AG400
AG600L 
AG400L
AG600LS
A1100S
AP250L 
AQ327
AQ550
AP200L

庆鸿CHMER慢走丝
Q53SL
CW-640
CW-530F
CW-350
gx430l
A5030L
A6040L
D433CL
D322CL
CM655
CM545
CM380
CM240R
CM420
CM655Z
CM545Z
CM434Z
CM323Z
A53CP
A43CP
A64CP 
CM3076C
CM2076C
CM1876C
CM1675C
CM1475C
CM1265C
CM1065C
CM865C
CM655C
CM A64C
CM A53C
CM A43C
CM434C
CM323C
AW1300L
AW1283F
AW1283L
AW1283S
AW9X
AW9L
AW9S
AW6X ( 3 side drop door )
AW6L ( Drop door )
AW6S
AW5X ( 3 side drop door )
AW5L ( Drop door )
AW5S
AW3X
AW3L
AW3S
SP3020L 
RX1283S浸水式
RX1065S浸水式
RX1065F喷水式
RX1063S浸水式
RX1063F喷水式
RX853S浸水式
RX853F喷水式
Q5030L
Q4025L
Q3020L 
G64S浸水式
G64F喷水式
G53S浸水式
G53F喷水式
G43S浸水式
G43F喷水式
G32S浸水式
G32F喷水式
GX640L
GX530L
GX430L
GX360L
EQ640L
EQ530L
EQ425L
EQ325L 
A422S浸水式
A422SL浸水式
SW-C30F
H1063F


西部SEIBU慢走丝
EW-450K1
M35A
M50A
M75A
MM35A
MM50A
MM75A
M25LP
M500S
M35B 
M50B 
M75B
MM35B 
MM50B
MM75B


夏米尔慢走丝
CUT20P
CUTE350
CUT2000
CUTE600
CUT30P
CUT200Sp
CUT300Sp
CUT2000S
CUT3000S
CUTE350
FORM20
FORM300
FORM400
FORM30
FORM200
DRILL20
240SLC
ROBOFIL510P
ROBOFIL290
ROBOFIL500
ROBOFIL380
ROBOFIL240
ROBOFIL390


徕通ACCUTEX慢走丝

 

亚特ART慢走丝

 


健升慢走丝

 

 


 三菱慢走丝维修：牧野、日立、西部、沙迪克、三菱、法那科、FANUC、ONA、阿奇、夏米尔、AMS、庆鸿、徕通、健升、精呈、和懋、美溪等品牌慢走丝维修苏三光 SPM

2019年12月26日 21:41
ꄘ浏览量：0
ꄀ收藏
ꂃ上一篇： 无
ꁹ下一篇： 无

深圳市诚弘欣科技有限公司

 

24小时联系电话：

 

13554907082 李工

 

 

  • ꁸ 回到顶部
  • ꂅ 13554907082
  • ꁗ QQ客服
  • ꀥ 微信二维码